Gm eprom programmer
![gm eprom programmer gm eprom programmer](https://www.usaspec.com/images/product/large/331_2_.jpg)
![gm eprom programmer gm eprom programmer](https://i.ebayimg.com/images/g/dSQAAOSwC6ZhPUPM/s-l300.jpg)
- #GM EPROM PROGRAMMER FULL#
- #GM EPROM PROGRAMMER SOFTWARE#
- #GM EPROM PROGRAMMER CODE#
- #GM EPROM PROGRAMMER PASSWORD#
- #GM EPROM PROGRAMMER PC#
Top 4 Reason to Get GM Tech2 Full Package:ġ. GM Tech2 Tech 2 GM Scanner with CANdi TIS Works for GM/SAAB/OPEL/SUZUKI/ ISUZU/ Holden
#GM EPROM PROGRAMMER PC#
#GM EPROM PROGRAMMER CODE#
If TDC offset is not programmed, a Diagnostic Trouble Code (DTC) P1214 will be set in the PCM. PCM uses the TDC offset to determine proper fuel injection pump timing. The PCM has the ability to determine the amount of offset required to bring the engine to TDC. This will allow TDC offset to be programmed into the PCM if necessary.
![gm eprom programmer gm eprom programmer](https://i.ebayimg.com/images/g/xPYAAOSwySthPUPL/s-l300.jpg)
If the crankshaft position sensor, engine or PCM with fuel injection pump were replaced, perform TDC offset learn procedure.Ĥ.Start engine and warm engine until engine coolant temperature is at least 170 Deg F. Once PCM is programmed, if only the PCM was replaced, go to next step.
#GM EPROM PROGRAMMER PASSWORD#
If EEPROM programming still fails, replace PCM.ģ.Perform password learn procedure for anti-theft system using proper procedure. NOTE: If PCM programming fails, ensure all electrical connections on PCM are okay. If PCM is not programmed, a Diagnostic Trouble Code (DTC) will be set in the PCM. Powertrain Control Module (PCM) Programming (6.5L Diesel)ġ.If PCM was replaced, the PCM must be programmed. Once Crankshaft Position (CKP) sensor variation learn procedure and password learn procedure for anti-theft system are performed, perform powertrain On-Board Diagnostic (OBD) system check. Once password learn procedure for anti-theft system has been performed, perform powertrain On-Board Diagnostic (OBD) system check.ĥ.Once EEPROM is reprogrammed, Crankshaft Position (CKP) sensor variation learn procedure and password learn procedure for anti-theft system must be performed using proper procedure. On models except Calif., go to step 5).Ĥ.Once EEPROM is reprogrammed, password learn procedure for anti-theft system must be performed using proper procedure. Verify vehicle application by using underhood Emission Control label.ģ.Once EEPROM is reprogrammed, use the Scan Tool to reset Idle Air Control (IAC) valve. DO NOT perform CKP sensor variation learn procedure on Calif. NOTE: Crankshaft Position (CKP) sensor variation learn procedure should ONLY be performed on Except Calif. If EEPROM is not programmed, a Diagnostic Trouble Code (DTC) will be set in the VCM. If EEPROM programming still fails, replace VCM.ģ.Once EEPROM is reprogrammed, Crankshaft Position (CKP) sensor variation learn procedure and password learn procedure for anti-theft system must be performed using proper procedure.Ĥ.Once Crankshaft Position (CKP) sensor variation learn procedure and password learn procedure for anti-theft system are performed, perform powertrain On-Board Diagnostic (OBD) system check.Įlectronically Erasable Programmable Read Only Memory (EEPROM) Programming (7.4L)ġ.If Vehicle Control Module (VCM) was replaced, the EEPROM in the VCM must be programmed. NOTE: If EEPROM programming fails, ensure all electrical connections on VCM are okay.
![gm eprom programmer gm eprom programmer](https://i.ytimg.com/vi/GdxYQdxYE5g/hqdefault.jpg)
#GM EPROM PROGRAMMER SOFTWARE#
Perform EEPROM programming using the Techline equipment manufacturer’s instructions and latest software applicable for the vehicle model. Ensure cable at Data Link Connector (DLC) and the SPS Device are properly connected. If EEPROM is not programmed, a Diagnostic Trouble Code (DTC) will be set in the VCM.Ģ.Ensure battery is fully charged. California emissions may be available in other states.Įlectronically Erasable Programmable Read Only Memory (EEPROM) Programming (4.3L, 5.0L & 5.7L)ġ.If Vehicle Control Module (VCM) was replaced, the EEPPOM in the VCM must be programmed. NOTE: References to California models apply to California emission vehicles, which may be verified by underhood Emission Control label. NOTE: Read all procedures listed to determine why and when each procedure is to be performed before proceeding. (1) – Vehicle series is fifth character of VIN. 4WD Blazer, Bravada, Jimmy, Pickup & Sonoma